Multi-brand automation spare parts and integration support.Email: contact@mail.warrior-tech.com
Pneumatic AutomationWZ-APP-0102

High-Speed Diaper Converting Line: Which Actions Suit Pneumatics and Which Do Not

A function-by-function guide to using pneumatics on diaper converting lines for reject gates, path switching, roller loading, and closed-loop web guiding.

High-Speed Diaper Converting Line: Which Actions Suit Pneumatics and Which Do Not
High-Speed Diaper Converting Line: Which Actions Suit Pneumatics and Which Do Not

A high-speed diaper converting line contains many motions, but they do not all need the same actuator technology. Pneumatics are well suited to short, discrete actions such as switching a reject path or placing a guide element into a validated state. A simple two-position cylinder is usually a poor substitute for continuous web-guiding control that must make small corrections from live edge feedback. The useful question is not whether pneumatics are fast. It is whether the motion, feedback, positioning resolution, force behavior, and failure state match the process.

Define the Nonwoven Converting Application

This application belongs in a nonwoven products factory on a diaper or wet-wipe converting line. The equipment includes material-path baffles, reject gates, loading rollers, and web-guiding assemblies. The manifest pneumatic tasks are driving guide rollers, rejecting defective products, and switching material paths with cylinders, valve terminals, proportional pressure regulators, and sensors.

Festo identifies diapers, wipes, filters, and medical gowns as nonwoven converting applications on its official converting industry page. That industry statement supports using automation in the line. It does not mean every high-bandwidth web correction should be assigned to a conventional pneumatic cylinder.

Classify the Motion Before Selecting the Actuator

Start with the required motion profile and evidence. A reject gate usually has two defined states and acts only when a defect reaches its station. A path-switching baffle may also have discrete positions, but it must move inside a product gap or other validated window. Continuous edge guiding is different: the controller measures lateral error and commands small corrections while the web remains in motion.

Line function

Motion character

Pneumatic fit

Key condition

Defect reject gate

Short, discrete, two-state move

Often suitable

Product tracking and confirmed gate position are reliable

Planned path diverter

Discrete move at a defined transition

Often suitable

Web tension and collision risk are controlled during switching

Roller loading

Adjustable force or pressure state

Potentially suitable

Force geometry and dynamic response are validated

Dancer loading

Controlled force with continuous position interaction

Suitable only as an engineered loop

Pneumatic response is coordinated with the drive controller

Continuous edge guide

Small corrective positioning from live edge error

Simple two-position action is not suitable

Use a true closed-loop guiding architecture

Registration axis

Precise multi-position motion synchronized to product

Technology depends on performance need

Positioning, acceleration, and error recovery must be proven

This table is a screening tool, not a component selection. Servo-pneumatic, electromechanical, hydraulic, or hybrid systems may each be valid when the complete control loop meets the requirement.

Use Pneumatics for a Timed Reject Sequence

A defect inspection system identifies a product and transfers its position through the line controller. Before the defect reaches the reject station, the controller checks that the reject bin or alternate path is available and that the gate starts from its proven normal state. The valve terminal commands the cylinder at the calculated time. Position feedback confirms the reject state before the defective item enters the decision point.

After the tracked product clears, the gate returns and proves its production state. If either transition is late or missing, the response should protect subsequent products and prevent a second uncoordinated command. A cylinder sensor confirms actuator position, not successful removal of the diaper. Where escape has a significant quality consequence, add downstream product confirmation.

Reject stage

Required data

Pneumatic action

Acceptance evidence

Detect

Defect identity and encoder position

None

Product entered the tracking queue

Prepare

Path availability and current gate state

Precondition valve output if designed

Normal position and pressure state accepted

Divert

Calculated arrival window

Extend or rotate the gate

Reject position reached before product arrival

Verify

Downstream product or bin signal

Hold state through the qualified window

Defective product is accounted for

Reset

Clearance of tracked item

Return gate

Production position confirmed before next product

Commission this sequence at the fastest approved line condition and with actual product spacing. A timer derived from low-speed setup is not sufficient.

Do Not Turn a Two-Position Cylinder into an Edge Guide

Web edge error changes continuously. A proper guiding system combines an edge or line sensor, controller, actuator, guide geometry, and tuned response. Maxcess describes dedicated web guiding solutions that use sensors, controllers, and proportional corrective actuators for converting and printing applications. That first-party equipment overview illustrates why continuous guiding is a loop, not a repeated extend-retract command.

A simple cylinder that pushes left or right only after error crosses a threshold can hunt around the target, shock the web, and interact badly with tension. Adding faster valves does not create intermediate positioning or stable loop dynamics. If pneumatics are retained, use a genuine proportional or servo-pneumatic concept with position feedback and validated bandwidth, friction, air volume, and control logic.

Coordinate Roller Loading with Web Tension

Pneumatic pressure can provide adjustable loading for a dancer or guide roller, but the drive still controls web transport. Festo describes intelligent dancer roller control for textile, film, and paper webs. The example shows a regulated pneumatic approach, not permission to treat every roller as a two-state actuator.

Define which loop owns tension, which signal commands pressure, and how dancer position changes the unwind or rewind drive. Cylinder friction, linkage geometry, tubing volume, regulator response, roller inertia, and drive tuning all affect the result. A pressure reading alone does not prove material tension.

Engineer Path Switching Around the Web State

A material-path baffle should move only when the web or discrete product flow is in a state that tolerates the transition. The controller must know the baffle position, line speed, web tension condition, nearby roller clearance, and location of splices or products. If switching requires a gap, verify the gap rather than assuming that a command created one.

Define the response to lost air, a stuck baffle, missing position feedback, and restoration of control power. Depending on mechanics and web load, a pneumatic actuator may drift, remain trapped, or move under gravity after supply loss. The required state comes from the machine risk assessment and process analysis.

Size for Response at the Point of Use

Valve catalog switching time is only one part of total response. Controller scan, network update, valve actuation, tubing volume, pressure, cylinder load, cushioning, friction, and sensor delay all contribute. Measure command-to-mechanism motion on the assembled machine at specified supply and environmental limits.

Place valve terminals and tubing to support maintainability and the required response without exposing components to fiber buildup or cleaning damage. Use flow controls to tune impact after the actuator is correctly sized. Do not compensate for an undersized valve, binding linkage, or excessive moving mass by raising pressure without analysis.

Handle Fibers, Dust, and Maintenance Access

Nonwoven fibers can collect on guides, sensors, exhaust silencers, and valve islands. A loaded silencer changes exhaust behavior and may slow a reject gate. Adhesive overspray and lotion from some product formats can alter friction or attack materials. Select protection and compatibility from current component data and the plant's actual cleaning agents.

Design access so operators can clear a product without reaching into an active reject or guide mechanism. ISO 12100:2010 provides the machinery risk-assessment process, and ISO 4414:2010 addresses pneumatic fluid-power hazards. Ordinary valve and sensor channels are not safety functions unless the complete architecture is designed and validated as such.

Validate by Function, Not Technology Label

For each pneumatic action, record the required stroke, load, response window, position evidence, permitted error, cycle demand, air behavior, and fault state. Test representative product sizes, maximum qualified speed, web tension range, fiber loading, low permitted supply, planned stops, web breaks, and safely injectable sensor faults. Trend late-gate alarms and actuator response before they become reject escapes.

The related slitter air shaft sequence shows why another web-line pneumatic function also needs state coordination with rotation and stored energy. Candidate families can be reviewed in the WarriorZ pneumatic component catalog.

WarriorZ supplies pneumatic and industrial automation components and helps compare product families from documented performance inputs.

Official Technical References

Sources and verification basis

These references support the documented facts, calculations, or engineering boundaries used in this article.

Evidence basis: Festo identifies diaper and wipe converting plus controlled dancer loading, Maxcess documents dedicated web-guiding loops, and ISO sources establish machinery and pneumatic safety boundaries.
  1. Innovative solutions for the converting industry
  2. Web guiding solutions
  3. Intelligent control for constant web tension
  4. ISO 12100:2010 Machinery risk assessment and risk reduction
  5. ISO 4414:2010 Pneumatic fluid power safety requirements